UDC 528.3
CSCSTI 36.23
The transfer of coordinates to the mounting horizons is the most important stage in creating an internal center base. The paper presents an analysis of all possible transmission methods and their subsequent synthesis that meet the requirements of high-rise construction. For each of the selected methods, the most rigorous scheme for calculating accuracy is presented. In order to automate computing processes, a software product was created that allows calculating the accuracy of all selected methods.
creation of an internal center base, transfer of coordinates to mounting horizons, accuracy calculation, zenith device, inclined design, reverse serif, global navigation satellite system, design automation, software development, computerization
1. Vizirov YuV. Razvitie izmeritel’nykh tekhnologii peredachi proektnykh osei I vysot na montazhnye gorizonty [Development of measurement technologies for transferring design axes and heights to installation horizons]. Measurements World. 2015;1: 16–24. (In Russian).
2. Yandrov IA. Nekotorye aspekty primeneniya koordinatnogo metoda razbivochnykh rabot v stroitel’stve [Some aspects of the application of the coordinate method of center work in construction]. Izvestia vuzov. Geodesy and Aerophotosurveying. 2004;5: 41–47. (In Russian).
3. Kalugin YuV. Vyverka konstruktsii I sooruzhenii po vertikali [Vertical reconciliation of constructions and structures]. Construction materials, equipment, technologies of the XXI century. 2013;10: 38–39. (In Russian).
4. Nikonov AV. Sposobi peredachi koordinat na montazhnye gorizonti [Methods to coordinate transfer on assembly level]. Proceedings of the XIII International Scientific Congress and exhibition “Interexpo Geo-Siberia 2017”. International Scientific Conference “Geodesy, Geoinformatics, cartography, surveying”. 2017;1(1): 3–9. (In Russian).
5. Vasilyuk TS. Issledovanie metodov peredachi tochek planovogo obosnovaniya na montazhnyi gorizont na otkrytoi mestnosti [Investigation of the methods of horizontal control points transfer on assembly level in open terrain]. Molodoi issledovatel’ Dona. 2018;6: 12–15. (In Russian).
6. Nesterenok MS, Rak IE, Veksin VN. Effektivnost’ vertikal’nogo proetsirovaniya osevykh tochek elektronnym takheometrom pri stroitel’stve zdanii I sooruzhenii [Vertical Projection Efficiency of Pivot Points Using Electronic Tacheometer During Construction of Buildings and Structure]. Science & Technique. Series 2. Civil and industrial engineering. 2014;5: 35–39. (In Russian).
7. Shekhovtsov GA. Edinyi algoritm uravnivaniya, otsenki tochnosti i optimizatsii geodezicheskikh zasechek [A unified algorithm for equalizing, evaluating accuracy and optimizing geodetic serifs]. Nizhniy Novgorod: Nizhny Novgorod State University of Architecture and Civil Engineering, 2017. 123 p. (In Russian).
8. Shekhovtsov GA. O tochnosti opredeleniya punkta, raspolozhennogo v zamechatel’nykh tochkakh treugol’nika [On the accuracy of determining the point located in the remarkable points of the triangle]. Izvestia vuzov. Geodesy and Aerophotosurveying. 2020;64(6): 627–634. (In Russian). DOIhttps://doi.org/10.30533/0536-101X-2020-64-6-627-634.
9. Shekhovtsov GA. O sozdanii planovoi razbivochnoi seti sposobom obratnoi lineino-uglovoi zasechki pri stroitel’stve zdanii povyshennoi etazhnosti [About building a planned center network by means of inverse linear-angular notches in construction of high-rise buildings]. Privolzhsky Scientific Journal. 2019;4: 98–107. (In Russian).
